Motorised Roller Blinds - Tapestry & Serenity
Serenity: Stone with Battery Powered Motor (M2879)

It’s something that we get asked how to do all the time, so you will be happy to know our easy-to-follow guide has all your bases covered. Here’s everything you need to know for our New Zealand windows.

• Reach for your metal tape measure - its the very best tool for the job.


• You only need to know the width and the drop (length) - its that easy.


• You will need to select between the three options for fitting...

1) Measuring for Inside Fitting Blinds

• Step 1: Measure the width of the inside of the frame; across the top, bottom and middle. Write down the smallest of the three measurements.


• Step 2: Measure the drop (length) of the inside of the frame across the left, middle and right. Write down the smallest of the three.


• Step 3: Check that you have enough clear space inside the window to mount the blind. you will need 60 mm for a single roller blind and 100 mm for a double roller blind.


• Step 4: When ordering your blind, select the “inside (Frame)” option.


• Step 5: When ordering your blind, select “front roll” option. This means that the fabric will roll off the front of the roll to avoid any latches, or other hardware inside the frame.

2) Measuring for Outside Fitting Blinds:

• Step 1: Measure the outside of your window recess from one side to the other. You should be starting and finishing where you want the outside edges of the brackets to be.


• Top Tip: For best results allow your blind to overlap the edges of the recess by at least 50 mm on each side. - ensuring that you have enough space to accommodate the suggested overlap.


• Step 2: Measure your recess from top to bottom, starting from where you want the brackets to be and ending where you want the bottom of the blind to be.


• Step 3: When ordering your blinds, select the “outside” fit option.


• Step 4: When ordering your blinds, select back roll. This means that the fabric will roll off the back of the roll to ensure the fabric stays close to the architrave for maximum privacy and light control.

3) Measuring for Blinds to be Mounted on an Architrave

• Step 1: Measure across from outside edge of architrave to outside edge of architrave. Again, you should be starting and finishing where you want the outside edge of the brackets to be this will be your width measurement


• Step 2: Measure from the top to the bottom of your archtrave, this will be where your blind brackets sits at the top and where the bottom of your blind finishes - this will be your height measurement.


• Step 3: When ordering your blinds select the “Architrave” fit option.


• Step 4: When ordering your blinds select the “back” roll option. This means the fabric will roll off the back of the roll to ensure the fabric stays close to the architrave for maximum privacy, light control and better insulation.

Our motorised blinds are installed like any other roller blind. Simply follow our handy fitting guides that come with your order and we will also send you some simple instructions for configuring your motorised blind to set the top and bottom limits. You may need to engage an electrician to bring power to the units if you choose our mains powered option, but the battery powered units install just like any of our other 'easy install' blinds.

There are two ways your roller blinds may roll - either front roll or back roll.

Front Roll

Back Roll

This is quite a common problem. Your window will require two blinds. Please contact us or phone us on 0800 763 748 so we can discuss the best options with you.

Yes, it is possible to link blinds in the same window. Please see specific questions below and refer to our linked blind page.

Determine which is the through blind as shown in the diagram below. We generally recommend that the through blind is the main window or where you achieve the most privacy to stop vision down the gap between the butting blind.

1. Take the width measurement of the Blind 1 (run through blind).

2. Take the width measurement of the Blind 2 (butt blind).

3 Apply deduction to the Blind 2 (butt blind) see table below. The deduction of the butt blind allows the blind to butt up to the through blind.

4. Measure the drop of each blind in 3 places and take your smallest measurement.
We recommend front roll to help minimise the gap.

Measure your Butt Blind (Blind 2) by taking the exact back wall measurements less the deduction shown in the table above.

We usually take between seven to twelve working days to process orders for sunscreen blinds, blackout roller blinds, venetian blinds, curtain rods and tracks and ready made curtains. If there is a delay ,you will be notified at time of placing your order. If you require your order by a certain date, please let us know and we will do our best to meet your deadline.
On our Easy-Fit curtain track range , we have same day dispatch on your order. As long as we receive your order by 1pm it will be dispathed that day . Delivery is usually the next day for most North Island customers and three days for most of the South Island. Our three day dispatch blinds will be sent within three working days.

Rods and Blinds are always happy to help you place your order over the phone, especially if you need some expert advice about the products before you buy. Just call us on 0800 763 748 and speak to one of our trained advisors

We accept all major credit cards, account to account, and direct credit.

Your curtains and roller blinds have been designed to be easy to install. They come with step by step instructions with clear photos of each step. Our instructions are backed up by our 0800 number and we are happy to help.